|
|
|
|
|
|
|
|
|
|
|
|
|
|
The WBSK workbench and shelving hardware kit provides the connectors and connector fasteners to build a workbench or shelving unit. The kit features the Simpson Strong-Tie? Rigid Tie? RTC2Z corner connector that makes it easier to make strong and durable corner connections with 2 x 4 lumber using no angle cuts or bolts. Each kit contains enough RTC2Z connectors to construct one workbench. Two kits are necessary to build a four-shelf unit. With the WBSK kit, a professional quality project can be customized and completed in a couple of hours.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
The BP is designed to provide a greater bearing surface than standard cut-washers and help distribute the load at critical connections. This bearing plate works by transferring concentrated compressive forces between two structural elements. The BP is available with a hot-dip galvanized (HDG) coating to protect the plate from corrosion when exposed to the elements or certain types of treated lumber.
|
The BP is designed to provide a greater bearing surface than standard cut-washers and help distribute the load at critical connections. This bearing plate works by transferring concentrated compressive forces between two structural elements. The BP is available with a hot-dip galvanized (HDG) coating to protect the plate from corrosion when exposed to the elements or certain types of treated lumber.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The BP is designed to provide a greater bearing surface than standard cut-washers and help distribute the load at critical connections. This bearing plate works by transferring concentrated compressive forces between two structural elements. The BP is available with a hot-dip galvanized (HDG) coating to protect the plate from corrosion when exposed to the elements or certain types of treated lumber.
|
Bearing plates give greater bearing surface than standard-cut washers and help distribute the load at these critical connections. The LBPS are bearing plates that offer increased flexibility while meeting the latest requirements of the code for 2 x 4 and 2 x 6 walls. The slotted hole allows for adjustability to account for bolts that are not in the middle of the sill plate.
|
The BP is designed to provide a greater bearing surface than standard cut-washers and help distribute the load at critical connections. This bearing plate works by transferring concentrated compressive forces between two structural elements. The BP is available with a hot-dip galvanized (HDG) coating to protect the plate from corrosion when exposed to the elements or certain types of treated lumber.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Bearing plates give greater bearing surface than standard-cut washers and help distribute the load at these critical connections.
|
The HTT is a high-strength solution for resisting tension loads in post-pour, wood-to-concrete connections. This heavy, single-piece formed tension tie is fastened with nails or Strong-Drive? SD Connector screws. The HTT has a four-ply formed seat and a design without rivets that does not require washers.
|
The BP is designed to provide a greater bearing surface than standard cut-washers and help distribute the load at critical connections. This bearing plate works by transferring concentrated compressive forces between two structural elements. The BP is available with a hot-dip galvanized (HDG) coating to protect the plate from corrosion when exposed to the elements or certain types of treated lumber.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The BPS is designed to provide a greater bearing surface than standard-cut washers and help distribute the load at critical connections. This bearing plate features a slotted hole that allows for adjustability to account for bolts that are not in the middle of the sill plate. The BPS offers increased flexibility while meeting the latest code requirements for 2 x 4 and 2 x 6 walls.
|
The CNW is designed to connect threaded rods to one another and to anchor bolts. These coupler nuts are designed to exceed the specified minimum tensile capacity of the corresponding bolts and threaded rod. All CNW coupler nuts feature a positive stop to help ensure even threading into each end of the nut and a Witness? hole as a means to verify when rods are properly installed.
|
The HTT is a high-strength solution for resisting tension loads in post-pour, wood-to-concrete connections. This heavy, single-piece formed tension tie is fastened with nails or Strong-Drive? SD Connector screws. The HTT has a four-ply formed seat and a design without rivets that does not require washers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The CNW is designed to connect threaded rods to one another and to anchor bolts. These coupler nuts are designed to exceed the specified minimum tensile capacity of the corresponding bolts and threaded rod. All CNW coupler nuts feature a positive stop to help ensure even threading into each end of the nut and a Witness? hole as a means to verify when rods are properly installed.
|
When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
|
|
