|
|
|
|
|
|
|
|
|
|
|
|
|
|
Prevents submersible power cable from rubbing against side of the well. Made from strong polyethylene. Adjustable for 4 to 6 in casing. Easy to use, snap-in wire guide. With split circle wire hole.
|
Water Source Cable Guard, Suitable for: 4, 5, 6 in Well Casings
|
Wire sizes 3-wire 10-12-14. Sleeve size 3/8 in x 3 in.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For all charging applications. For use with conventional tanks.
|
Water Source Flush Pipe Coupling, Nominal Size: 1-1/4 in, Slip Connection, Schedule Rating: SCH 40, PVC
|
Compression sleeve for 3 wire. Wire sizes for 3 wire 10-12-14 submersible cable.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Lead-free, steel case, brass mount. 1/8 in CBM connection.
|
Suitable for air, steam or water. Easy to read dial face. Steel case with glass face, accurate reading assured. Brass socket connection.
|
Suitable for air, steam or water. Easy to read dial face. Steel case with glass face, accurate reading assured. Brass socket connection.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Water Source Flat Valve, Leather, Dimensions: 3-1/2 x 1-7/8 in
|
This heat shrink splice kit comes with four clear tubes and four connectors. These tubes are designed to shrink around the electrical wire. The shrink kit works with #14, #12 and #10 ga submersible wire.
|
Water Source Inline Sump Check Valve, 1-1/2 in Nominal, MNPT Connection, PVC Body
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Water Source Pool Pressure Gauge, Gauge Case Material: Steel, 1/4 in Connection, Measuring Range: 100 psi, Lens Material: Glass
|
The pressure gauge measures water pressure in the pressure tank. It has a 1/4 in lower connection. Dark numbers are easy to read on the gauge.
|
Plastic and wax impregnated oak-tan leather cups for regular service. #3x2, use with #2 pitcher pump for 3 in cylinder. #31/2x21/4, use with #3 pitcher pump for 31/2 in cylinder.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For all charging applications. For use with conventional tanks.
|
The pitcher pump leathers are used in pitcher pumps. Prime the pump before each use. When wet, leathers will expand to create an air tight seal.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The pressure gauge measures water pressure in the pressure tank. It has a 1/8 in back connection. Dark numbers are easy to read on the gauge.
|
The 1-1/4 in well point drive coupling connects the well point to the drive pipe. The galvanized steel construction withstands the pounding force necessary to drive a well point into the ground. The design assures a tight joint at the pipe.
|
The 1 in male adapter with the rope loop connects flexible poly pipe to the barbed end and a threaded iron pipe to the female end. To minimize leaks, make sure all connections are tight. Use thread tape on all threaded connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Eco-Flo Pitcher Pump Kit, Leather, Includes: Flat Leather Valve and Leather Cup
|
Water Source Pressure Gauge, 3/4 in Connection, Female Connection, Measuring Range: 0 to 100 psi, Dial Size: 2 in, Lens Material: Glass, Socket Material: Brass, Suitable for: 3/4 in Male Hose
|
The 2 in well point drive coupling connects the well point to the drive pipe. The galvanized steel construction withstands the pounding force necessary to drive a well point into the ground. The design assures a tight joint at the pipe.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Water Source Air Volume Control, Specifications: 3/8 in MPT Connection, Suitable for: 120 gal Water Tank
|
Fits 1 in or 1-1/4 in drop pipe, 4 in to 8 in well casing. Supplied with two stainless steel clamps.
|
Water Source Pressure Switch, 115/230 V, Dimensions: 3 in L x 4 in W x 4 in H, Steel Body, Gray, 30, 50 psi Working, Suitable for: Submersible Well or Jet Pumps
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Water Source Pressure Switch, 115/230 V, Dimensions: 3.95 in L x 3.75 in W x 3.95 in H, Steel Body, Gray, 40, 60 psi Working, Suitable for: Submersible Well or Jet Pumps
|
The 20/40 psi pressure switch signals the pump to start when the water system drops to a preset (e.g. 20 psi) and stop at high-pressure mark (e.g. 40 psi). This switch is to be used with submersible well pumps or as a replacement switch. It can be wired 115/230 V.
|
Water Source Pressure Switch, Dimensions: 3.95 in L x 3.75 in W x 3.95 in H, Working Pressure: 20 to 40 psi
|
|
|
